Specialty Mortars: Industrial, Screed, Tile, and Monocapa
Specialty Mortars
Industrial Mortars
Industrial wet mortar is a pre-mixed, ready-to-use product. Its components—conglomerates, sand, water, and/or additives—are precisely measured and mixed at a factory. This ensures consistent quality and cost-effectiveness. The additives maintain workability and prevent drying, making it ideal for various applications.
Cement Screed
: are special rules for land for new or restoring beams are dry mortars, cements and special additives. It comes in powder ready for use. Va bagging. Qualities:
Compressive strength: Measured by samples undergoing load to failure. High wear resistance and high adhesion. Good resistance to wear. Adherence is very important in these mortars. They combine maximum adhesion with minimal shrinkage. Water resistance: No experience and level expansion Smooth seamless: With low shrinkage, high adhesion, these products have no need of joints. These soils are considered to be seamless and free of imperfections. High productivity: High productivity in the application of soil. They provide: Performance up to 300 m2/hr. Are only required for the application. Fast drying, allows foot traffic after 2-3 hours and heavier traffic after 24 hours. Minimal disruption to the work of the factory. Completely smooth and level floor. Quality and security: Companies are supplying this product to quality control in the application of your product and ensure that their products have a high suitability for building and renovating houses, offices.
MORTAR TAIL are materials for laying ceramic tiles. Highlights: The pieces can be larger. Absorption, ceramic tile manufacturers have developed products with a lower absorption up to the porcelain tile with takeovers virtually nil. Composition: Cement gray or white, depending on the color you want to. Arid selected for quality and fineness. Retaining water. Resins. Accelerators.
Role of components: Retainers of water: its main function is to retain the water from the mass of the mortar, obtaining a slow drying of the same, so there is a transfer of cement to the support and the workpiece. The slower the transfer, the more likely they will get the desired adhesion. Resins: we are polymers mainly incorporate chemical bonding and elastic modulus decreased. Additional advantages are improved workability, water retention, lower water absorption. Accelerators, used in specific cases of rapid setting adhesive on site. Reduce the curing time. Adhesion mechanics: mechanical adhesion is based on the interlocking between solids. Normally, a material applied to a plastic state on the surface of another, which should provide sufficient anchoring possibilities. Porous materials have generally a good surface to enhance mechanical grip, looking in some cases provided with reliefs or projections.Chemical bonding: the chemical bond and / or electrostatic active groups of the adhesive and the support or part. In cement-based adhesives are chemical bonding of resins. Measurement of adhesion: The quality of a ceramic coating on a work depends on a number of parameters that must be taken into account: Compatibility between rolling grip and support. Compatibility between the bonding mortar and pottery. Behavior of water. Flatness of the coating. Physical, chemical and mechanical solicitations. Water resistance. Thermal variations of the coating. Differential movements. Factors to start work: the media must have: Resistance: not degradable. Cleaning: no dust, oil, paint, etc.. Stability: good anchor associated with a design element. Flatness: media placement characterized with respect to plumbing, leveling and evenness. Absorption / Suction associated with the absorptive capacity of the supports and surface placement. Moisture: moisture content of the media placement or in the outer layers of the same. Placement: thin and thick layer. Double and single bonding. Execution: consists of two parts: Preparation of product-mixing: it should preferably be done with mixing / kneading machine hardly revolutionary, this operation will have the right length to get a homogeneous mixture and creamy, with a total absence of lumps and bubbles air. Placement: the adhesive is spread on the base or substrate with a trowel to obtain a uniform thickness. Then the entire surface of the paste applied is passed the notched trowel, ie “combing”, then put the tiles on the mass extended pressure by lightly tapping with a mallet rubber and moving them slightly to get the total collapse of the rows of adhesive so that good contact is achieved between the workpiece and the adhesive.
MORTAR MONOCAPA: special mortar aggregates composed of binders + + additives (always comes prefabricated.) Primary Function: Protection of building from the action of the elements: waterproof breathable support it. Aesthetic finish, decorative: they offer an aesthetic present noble and rural creativity and design that allows the designer to choose the color, texture, etc.. Classification-finished: Arid projected: the fine washed gravel or embedded. Shave finished with grooves left by the trowel to scrape it off. Rustico: is similar to the project, but the grains are thicker. Smooth, is the most durable, which is more waterproof. Features: Easy to apply: the additives give them a better work and greater application performance compared to traditional mortars. Speed of execution: using this mortar we finished the facade in operation, the traditional solution requires two phases (1. Applying a traditional mortar and 2. Application of a topcoat.) Economic savings: reduced manpower needed , shorter use of scaffolding, less delivery of the facade. Attributes: Deformability: can adapt to movements. Mechanical resistance: greater strength than traditional ones. Adherence: highly adhesive to use resins. Waterproof: more waterproof than the traditional but if transmitted. Durability: durability, improved support, particle size, additives, resistance. Light colors are more enduring because they repel the sun and prevent the expansion and cracking. Decorative: allow many finishes with a variety of colors.Composition: monolayer mortars are complex products, whose design makes use of all resources available to the modern technology. The formulation of mortars monolayer includes the following components: binders: nothing but white cement (cem bl) so that they can pigmented. Aggregates: marble. Additives: waterproofing, adhesives. Special fibers, fiber glass and PVC, prevent shrinkage, abrasion and give more grip. Pigments: to color. How to use: mainly the substrate must be clean, 95% of disease of the facades are caused by defects of the support to be inadequate or unprepared. It is essential to use eaves drips, fascia, etc.. Protection should start lining of the capillary moisture. It is recommended to use light shades coverings because they minimize the movement of thermal origin. Application: environmental conditions, should be placed in suitable environmental conditions: Storage: in dry and ventilated place, not the weather. Mixing: With the amount of water that marks the manufacturer. Execution: Normal plaster treatment.